Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Safe-O-Kid Unique High Density 2 Mtr Long U - Shaped 1 Edge Guard Strip - BrownSafe O Kid Unique High Density 2 Mtr Long U Shaped 1 Edge Guard Strip Brown Material: EVA Premium Edge guard, effectively cover the sharp edges while retaining its flexibility and softness for enhanced protection Thoroughly tested for high impact collisions (do not rupture) Best Quality Adhesives (do not come off easily yet do not leave stain damage furniture paint) Non Toxic, Eco Friendly, odorless, dust free and does not become sticky on prolonged
Safe-O-Kid Unique High Density 2 Mtr Long U - Shaped 1 Edge Guard Strip - Brown
Material: EVA
- Premium Edge guard, effectively cover the sharp edges while retaining its flexibility and softness for enhanced protection
- Thoroughly tested for high impact collisions (do not rupture)
- Best Quality Adhesives (do not come off easily yet do not leave stain/damage furniture/paint)
- Non-Toxic, Eco-Friendly, odorless, dust-free and does not become sticky on prolonged use even in Indian heat
- Flame Retardant/ Fire and water Resistance
- Easy to Install and Remove.
- Reusable.
- Vast Color and Design Choices to blend with furniture and/or room theme
- Flexible shapes and sizes to fit all furniture types and dimensions
Pre -install Safe-O-Edge with Corner Cushions. First install the corner cushions on all corners and then cut the edge guard into pieces to fit the space between corner cushions. Safe-O-Edge without Corner Cushions. Mark each corner on edge guard and cut the extra material (approx. 90Deg) using sharp knife for proper fit.
Installation
- Clean the sharp surface as well as Safe-o-Kids edge Cushions inner surfaces using any ordinary home cleaning solution. Wipe it dry.
- Peel off the yellow backing layer of the double sided tape provided with the edge Cushion
- Apply the tape to both inner surfaces of edge cushion
- Remove the 3M backings from the surfaces of edge cushion
- Carefully align the edge cushion so that it fits perfectly with the sharp surface without leaving any space
- Press tightly and hold edge Cushion against the surface for at least one minute
- Optionally, apply additional designer protection layer over the edge Cushion for additional strength, life and aesthetics.
DO NOT Use any chemicals/ sharp tools. - Clean the surface with wet cloth, etc as suitable
Legal Disclaimer: Product color may slightly vary due to photographic lighting sources or your monitor settings.
Product ID: 10480478
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.7 ★★★★★
Based on 62 reviews
Sort
Product Reviews
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024